What do De'Longhi coffee machine fault lights tell you?
De'Longhi coffee machine fault lights signal operating status and specific problems through steady, flashing or warning states. A one-cup, two-cup and warning light combination usually points to a failed extractor motor, which normally measures around 200 ohms. If resistance reads noticeably low or shows an open circuit, the motor is damaged. Checking the motor step by step while rotating it manually helps confirm this.
Circuit board protection matters during any inspection. A too-low motor resistance can mean the board is damaged too, so replacing the board first risks burning the new one out. If no relay click is heard after power is connected, the board likely needs replacement. Slow, dripping coffee flow often traces to two metal filter mesh pieces installed on the extractor; removing one usually resolves it.
During use of a De'Longhi fully automatic coffee machine, the indicator lights on the panel convey the machine's operating status and fault information through different states. Understanding the meaning of these light signals can help users quickly diagnose problems and take the correct measures. This article systematically compiles the common fault light behaviors of De'Longhi coffee machines, including warning lights turning on, lights flashing, lights staying steadily on, and other situations, and provides detailed troubleshooting steps and repair suggestions for specific problems such as extractor motor damage, coffee flow being too slow, grinder blockage, and groundskeeper being full. It also reminds users to pay attention to circuit board protection during inspection and repair to avoid secondary damage caused by improper operation.
Professional coffee knowledge exchange. For more coffee bean information, please follow Coffee Workshop (WeChat public account: cafe_style)
De'Longhi coffee machine fault light diagram De'Longhi coffee machine indicator lights
One cup, two cups, warning light on.
This situation is very likely due to a fault in the extractor motor. Normally, the motor's proper resistance value should be around 200 ohms. If the measurement result is noticeably low or directly shows an open circuit, it can be determined that the motor has been damaged. It should be noted that this motor is a DC type, so when measuring, the motor must be rotated manually and the resistance checked step by step.
If the measured resistance is too small, the circuit board may also have been damaged, so the circuit board should not be replaced rashly first; otherwise, the new board may be burned out again by the motor. In addition, if no sound from the relay on the circuit board can be heard after power is connected, it can basically be determined that the circuit board needs to be replaced.
When the coffee comes out, it drips rather than forming a stream.
When an automatic coffee machine is first purchased, the first few uses are often completely normal, but after several uses, the above situation may occur, and the coffee powder coarseness may still be within a reasonable range when checked. At this time, check whether two pieces of metal filter mesh have been installed on the extractor. If there are indeed two, remove one of them, and the problem will be readily solved.
De'Longhi fully automatic coffee machine light flashing. Its meanings are: 1. The coffee beans are ground too fine, causing the coffee output speed to be very slow. Handling method: make another cup of coffee. When the grinder is grinding beans, turn the grind adjustment knob one notch clockwise toward "7". If the coffee output speed is still slow after making at least 2 cups of coffee, turn the grind adjustment knob one more notch. 2. The coffee machine cannot make coffee. Handling method: if the problem still exists, turn the steam knob to the "ON" position to release some hot water from the milk frother.
The light stays steadily on. Its meanings are: the groundskeeper is full or has not been put back in place after cleaning. Handling method: empty and clean the drip tray and groundskeeper, then put them back in place. Note: when removing the drip tray, the groundskeeper must be emptied, even if there is only a little residue; otherwise, when you continue making coffee, the groundskeeper may fill up faster than you expect and block the machine's operation.
Light flashing. Its meanings are: 1. If the coffee grinder is very noisy when working, it indicates that a small portion of coffee beans is clogged in the grinder. Handling method: you can directly contact the seller or the De'Longhi after-sales service center. 2. The "use pre-ground coffee powder function" was selected without adding coffee powder. Handling method: add coffee powder to the coffee powder channel or cancel the "use pre-ground coffee powder function." 2. The coffee beans have run out. Handling method: add coffee beans to the coffee bean container.
More exciting content recommendations:
Espresso machine repair: common faults and handling methods for De'Longhi coffee machines
Why the water shortage light on a De'Longhi coffee machine stays on - coffee, how to drink coffee
Why ground beans from a De'Longhi coffee machine do not come down and all turn into powder - coffee machine extractor cannot be removed
Coffee machine repair: common faults and handling methods for De'Longhi coffee machines
De'Longhi coffee machine grinder adjustment level manual, grinder disassembly and repair
The above content is compiled by CoffeeHunters, a coffee news website.
